The TTM 01-G is a reliable and accurate GPS and GLONASS (GNSS) clock with sub-microsecond timing that is used to synchronize IEDs (Intelligent Electronic Devices) in the power industry and other industries where precise and reliable timing is required. As with all Tekron GPS clocks, the TTM 01-G has electrically isolated outputs, providing excellent noise immunity. The TTM 01-G supports both NTP/SNTP and PTP (IEEE 1588v2).

Key Features:

  • Supports GPS and GLONASS
  • Independently isolated outputs
  • Isolated power supply
  • High output power line drivers
  • Low noise characteristics due to balanced pair distribution
  • UTC and LST with user defined DST options
  • Remote configuration over Ethernet
  • Configuration security
  • Remote firmware upgrades
  • Enhanced security and encryption that exceeds NERC CIP requirements

Input/Output Signals:

  • DC IRIG-B (Un-modulated, DCLS)
  • AM IRIG-B (Modulated)
  • Supports C37.118.1
  • Serial Strings
  • User defined pulses
  • Modified Manchester
  • DCF77
  • NTP/SNTP
  • PTP (IEEE 1588 v2)
Physical 
Design:UL94-V0 polycarbonate flame retardant din rail mount case with IP40 (Ingress Protection rating).
Measurements:(W) 72 mm x (D) 60 mm x (H) 90 mm
Weight:0.2 Kg
GNSS Receiver 
L1, C/ A code, 32 Channel Parallel-tracking receiver
Frequency:1598 MHz
Acquisition (Sensitivity):-155 dBm
Tracking (Sensitivity):-160 dBm
Oscillator – TCXO
Holdover characteristics operating at 25°C:– TCXO 1PPS drifts 0.55 ms over a 24 hour period. 
– Drift rate: 7 ppb per second
Standard Outputs 
TTL:1 x TTL Programmable output, 0-5 v, 150 mA (2 Pin Screw terminal).
IRIG-B (B00x / B22x) time code with selectable C37.118.1 and AFNOR S87-500 extensions, 
DCF77 time code, 
User defined pulse sequences: 
− Repetition rates from 20ms to 24 hours 
− Offsets and durations from 10ms to 24 hours
Timing Accuracy: <100 ns to UTC
Fiber:1 x Fiber Programmable output, 62.5/ 125 μm, λ 820
nm, compatible with multi-mode fiber.
IRIG-B (B00x / B22x) time code with selectable C37.118.1 and AFNOR S87-500 extensions, 
DCF77 time code, 
User defined pulse sequences: 
− Repetition rates from 20ms to 24 hours 
− Offsets and durations from 10ms to 24 hours
Timing Accuracy: <100 ns to UTC
Additional Outputs 
In addition to the Standard Outputs, one of the following output options are also available for the 
TTM 01-G:
TTL:1 x TTL Programmable output, 0-5 v, 150 mA (2 Pin screw terminal).
IRIG-B (B00x / B22x) time code with selectable C37.118.1 and AFNOR S87-500 extensions, 
DCF77 time code, 
User defined pulse sequences: 
− Repetition rates from 20ms to 24 hours 
− Offsets and durations from 10ms to 24 hours
Timing Accuracy: <100 ns to UTC
AM IRIG-B:1 x AM IRIG-B output, 9 Vpp, 120 ohm,(2 Pin screw terminal)
Timing Accuracy: <2 μs to UTC
Serial Strings:1 x RS232 Level serial strings output (2 Pin screw terminal).
NMEA-0183 ZDA NMEA-0183 RMC IRIG J-17 Tekron A—G: Seven protocols designed for plug and play compatibility with a wide range of equipment.
Timing Accuracy: <1.5 µs to UTC (Pulse or time code); <100 µs to UTC (Serial)
HV MOSFET:1 x HV MOSFET programmable output, 0-300 V, 1 A (2 Pin screw terminal)
Timing Accuracy: <100 ns to UTC
Ethernet UTP Connection
Physical:1 x RJ45 10/100 Ethernet UTP connector
or 1 x ST multi-mode fiber Ethernet available 
General:DHCP auto-configuration with fallback to ARP tested link-local address 
VLAN packet tagging 
Protocols Supported: 
ARP, UDP, ICMP, TFTP, DHCP, SNMP v1, v2c, v3 
Typical timing accuracy (at the Port): <100 ns to UTC
NTP:Stratum-1 NTP & SNTP time server 
Multicast & Broadcast server capability 
Optional MD5 authentication
SNMPv1, v2c & v3 support can be independently enabled 
Configurable v1, v2c community names and securitygroups 
Fully configurable via SNMP 
v3 User-based Security Module (USM) support 
USM authentication methods: MD5, SHA 
USM privacy methods: DES, AES 
USM MIB support
NotificationsSNMP trap generation v1, v2c & v3 
SNMPv3 traps can be authenticated & privatized via USM 
Syslog (RFC-3164 & 5424 verities)
PTP (IEEE 1588 v2 support)As per Ethernet Output section plus:- 
PTP (IEEE1588) v2 operation 
GrandMaster (GNSS) or ordinary clock functions 
Profile selection: 
– Default 
– C37.238 Power Profile (full support) 
– Telecom Profile (slave only) 
– 1-step tx, 1-step/ 2-step rx 
– Layer 2 or Layer 3 mapping 
– Peer to Peer and End to End delay support  Timing Accuracy: <100 ns to UTC
Environmental & Electrical
Power supply options: 
Power Drain: 
Operating Temperature: 
Humidity: 
Programmability
Windows based configuration software is available to be downloaded from the Tekron website. User adjustable options include:
Timing & Synchronization:Worldwide daylight savings and local time configuration using either rule based or fixed date methods.
Options that allow equipment checks prior to full installation and adjustable hold-over times to increase reliability in the case of poor GNSS coverage.
Adjustments to compensate for installation parameters such as delay of GNSS signal through antenna cable.
Programmable output options:IRIG-B (B00x / B22x) time code with selectable C37.118.1 and AFNOR S87-500 extensions.
DCF77 time code 
1 kHz square wave 
User defined pulse sequences: 
− Repetition rates from 20 ms to 24 hours 
− Offsets and durations from 10 ms to 24 hours 
− Resolution is 10 ms.
Serial Strings (only serial version):NMEA-0183 ZDA 
NMEA-0183 RMC 
IRIG J-17 
Tekron A—G: Seven protocols designed for plug and play compatibility with a wide range of equipment.

backtotop
ttm-01-g-safenergy-i-din-moxa-ti-vit-nam