Features and Benefits 

  • Front-end intelligence with patented Click&Go control logic, up to 24 rules
  • Active communication with MX-AOPC UA Server
  • Save time and wiring cost with peer-to-peer communication
  • Supports SNMPv1/v2c/v3
  • Friendly configuration via web browser
  • Simplify I/O management with MXIO library for Windows or Linux platforms
  • Wide operating temperature range of -40 to 75°C (-40 to 167°F)

Introduction

Moxa’s ioLogik E2200 is a new type of Ethernet micro RTU controller, which is a PC-based data acquisition and control device that uses proactive, event-based reporting to control I/O devices. Unlike traditional RTUs, which are passive and must poll for data, Moxa’s ioLogik E2200 series with Active OPC Server makes seamless connection with SCADA systems a reality. In addition, SNMP is used for communicating with an NMS (Network Management System) for IT field users. The I/O status of an Ethernet micro RTU controller can be reported and controlled automatically on-site based on user specified conditions. This report-by-exception approach, which is new to PC-based monitoring, requires far less bandwidth than traditional polling methods.

 

Actice Alarming with Local Intelligence

The ioLogik E2200 Micro RTU supports simple and powerful Click&Go™ technology to deliver event-driven reports and allow alarm messages to be sent by email, TCP/UDP, and SMNP Trap with real-time stamps. With built-in Click&Go™ intelligence, the ioLogik E2200 micro RTU can be used for simple output control when it is triggered by input status, without the need for a PC controller. The ioLogik E2200 micro RTU reports I/O status automatically based on user-specified conditions. This report by-exception approach requires far less bandwidth than the traditional polling approach.

• ioLogik E2214 Specifications
• Inputs and Outputs
Digital Inputs6 channels
Relay Outputs6 channels
Isolation3k VDC or 2k Vrms
• Digital Input
Sensor TypeWet Contact (NPN or PNP) and Dry Contact
I/O ModeDI or Event Counter
Dry Contact• On: short to GND
• Off: open
Wet Contact (DI to GND)• On: 0 to 3 VDC
• Off: 10 to 30 VDC
Common Type3 points per COM
Counter Frequency900 Hz
Digital Filtering Time IntervalSoftware Configurable
• Relay Output
TypeForm A (N.O.) power relay
Contact Current Rating• Inductive Load: 2 A @ 30 VDC, 250 VAC, 110 VAC
• Resistive Load: 5 A @ 30 VDC, 250 VAC, 110 VAC
Minimum permitted load1 A @ 5 VDC
Initial Insulation Resistance1000 mega-ohms (min.) @ 500 VDC
Mechanical Endurance1,000,000 operations
Electrical Endurance100,000 operations @ 5 A resistive load
Contact Resistance100 milli-ohms (max.)
Pulse Output0.3 Hz at rated load
NoteAmbient humidity must be non-condensing and remain between 5 and 95%. The relays of the ioLogik E2214 may malfunction when operating in high condensation environments below 0° Celsius.
• Power Requirements
Input Voltage12 to 36 VDC
Input Current170 mA @ 24 VDC
• MTBF (mean time between failures)
Time307,239 hrs
StandardTelcordia SR332
• Common Specifications
• LAN
Ethernet1 10/100 Mbps RJ45 port
Protection1.5 kV magnetic isolation
ProtocolsModbus/TCP (slave), TCP/IP, UDP, DHCP, BOOTP, SNMP, HTTP, CGI, SNTP, SMTP
• Serial
Interface1 RS-485-2w terminal block port
ParityNone
Data Bits8
Stop Bits1
Flow ControlNone
Baudrate1200 to 115200 bps
ProtocolsModbus RTU (gateway)
• Physical Characteristics
WiringI/O cable max. 14 AWG
Dimensions115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weightunder 250 g (0.55 lb)
MountingDIN-rail or wall
• Environmental Limits
Operating TemperatureStandard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity5 to 95% (non-condensing)
ShockIEC 60068-2-27
VibrationIEC 60068-2-6
AltitudeUp to 2000 m
NotePlease contact Moxa if you require products guaranteed to function properly at higher altitudes.
• Standards and Certifications
SafetyUL 508
EMCEN 61000-6-2/6-4
EMICISPR 22, FCC Part 15B Class A
EMSIEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS:
80 MHz to 1 GHz: 10 V/m
1.4 GHz to 2 GHz: 3 V/m
2 GHz to 2.7 GHz: 1 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV
IEC 61000-4-5 Surge: Power: 1 kV
IEC 61000-4-6 CS: 10 V
IEC 61000-
Green ProductRoHS, CRoHS, WEEE
NotePlease check Moxa’s website for the most up-to-date certification status.
• Warranty
Warranty Period2 years
DetailsSee www.moxa.com/warranty

*Because of the limited lifetime of power relays, products that use that component are covered by a 2-year warranty.

Available Models

Model No.Description
ioLogik E2214Ethernet Micro RTU Controller with 6 digital inputs and 6 relay outputs, -10 to 60°C operating temperature
ioLogik E2214-TEthernet Micro RTU Controller with 6 digital inputs and 6 relay outputs, -40 to 75°C operating temperature

Compatible Modules

 LDP1602 LCD Module

Model No.Description
LDP1602LCD module with 16 x 2 text display and 5 buttons

Optional Accessories

 Trial Software

Model No.Description
MXviewIndustrial network management software designed for converged automation networks

Towards a Smarter World with Moxa’s I/O Solutions

Smart I/O Success Stories
The innovation of Moxa’s data acquisition engineers is reflected in Moxa’s latest I/O products, which are helping companies around the world simplify the management of distributed control systems, and as a result reduce costs and create business growth. In addition, Moxa also provides innovative data acquisition software that helps businesses simplify the process of integrating I/O devices with an existing network. This smart automation software not only helps users gather data faster and more efficiently, but also helps businesses identify, assess, and monitor potential risks.

Download this 16-page Smart I/O Brochure to learn more about:
– The Smarter World Trend 
– Moxa’s Innovative Designs
– Moxa’s Easy-to-Use Automation Software
– Success Stories Based on Moxa’s Smart I/O Solutions
– Moxa’s Smart IO Product Selection Guide

 

Related White Papers

A New Chapter in the Legacy of RS-485 Data Acquisition Devices
This white paper provides insight into the future of RS-485 data acquisition devices, and how Moxa is adding a new chapter to the legacy of RS-485 data acquisition devices.

 

SNMP I/O Devices Make Monitoring Environmental Conditions Easy
This paper will first explain what SNMP is, why you should use SNMP for environmental monitoring, and then discuss how an SNMP environmental monitoring device will help ease the management and implementation process.

    

Hardware Informations:

Dimensions

Pin Assignment

I/O (left to right)


backtotop