Phase-out and Last Buy Notice

The VPort 364A will be discontinued starting from April 1, 2017. The deadline for placing a final purchase order is August 31, 2017. Due to the limited availability of these products, orders will be processed till we run out of stock. For alternative solution, please contact your Moxa sales representative if you have further questions.

Features and Benefits

  • Dual simultaneous H.264 and MJPEG video streams
  • Video latency under 200 ms
  • Moxa DynaStream™ function support for network efficiency
  • ONVIF support for standardization and interoperability
  • 802.1X and SSL/SSH for advanced network security
  • Industrial design with -40 to 75°C operating temperature
  • VPort SDK PLUS provided free

Introduction

The VPort 364A 4-channel industrial video encoder with H.264 video compression algorithm provides the best video quality on the market, but with a smaller bandwidth requirement than other video compression standards. In addition, to meet various video stream requirements, the VPort 364A supports dual video streams using H.264 and MJPEG compression formats. The two video streams can be used for different purposes, such as viewing, recording, and analysis. In addition, the rugged industrial design, which includes a -40 to 75°C operating temperature range, IP30 form factor protection, and industrial certifications, make the VPort 364A highly suitable for use in harsh environments.

• Video
Video CompressionH.264 (MPEG4 part 10, AVC) or MJPEG
Video Inputs4, BNC connector (1.0 Vpp, 75 ohm)
Video StreamsDual streams (one for H.264, the other for MJPEG)
NTSC/PALManual
Video Viewing• DynaStream™ support for changing the video frame rate automatically
• Adjustable image size and quality
• Timestamp and text overlay
Video Resolution and FPS (frames per second) in single video stream
• Audio
Audio Inputs1, Line-in or mic-in with RCA connector
Audio Outputs1, Line-out with RCA connector
Audio FormatMono, PCM
• Network
ProtocolsTCP, UDP, HTTP, SMTP, FTP, NTP, DNS, DHCP, UPnP, RTP, RTSP, ICMP, IGMPv3, QoS, SNMPv1/v2c/v3, DDNS, Modbus/TCP
Ethernet1 10/100BaseT(X) auto negotiating RJ45 port, or 1 100BaseFX fiber port (single/multi-mode, SC connector)
• Serial Port
PTZ Ports1, RS-232/422/485 port (5-pin terminal block connector), max. speed of 115.2 Kbps
Console Port1, RS-232 RJ45 port
• GPIO
Digital Inputs4, max. 8 mAHigh: +13 V to +30 V; Low: -30 V to +3 V
Relay Outputs2, max. 24 VDC @ 1 A
• LED Indicators
STATSystem status
PWR1Power 1
PWR2Power 2
FAULTCan be configured to correspond to system alarm, power failure, or disconnected network
V1, V2, V3, V4Video input signal activity for channels 1 to 4
• Power Requirements
Input Voltage2 redundant power inputs, 12 to 32 VDC or 18 to 30 VAC, terminal block connector
Input Current12 to 32 VDC, 0.7 A (max.) or 18 to 30 VAC, 0.68 A (max.)
Power Consumption7.5 W (max.)
• Physical Characteristics
HousingMetal, IP30 protection
Dimensions80.2 x 135 x 105 mm (3.16 x 5.31 x 4.13 in)
Weight1.13 kg (2.49 lb)
InstallationDIN-rail mounting (standard), wall mounting (optional)
• Alarms
Video Motion DetectionIncludes sensitivity tuning
Video LossVideo loss alarm
SchedulingDaily repeat timing schedule
ImagingJPEG snapshots for pre/trigger/post alarm images
Custom AlarmsHTTP event servers and CGI events for setting customized alarm actions
Email/FTP MessagingAutomatic transfer of stored images via email or FTP with event-triggered actions
Pre-alarm Buffer24 MB per channel for JPEG snapshot images
• PTZ (Pan/Tilt/Zoom)
PTZ Camera ControlVia RS-232/422/485 PTZ port
PTZ Control FunctionsPan, tilt, zoom, focus, moving speed, preset position (max. 25 positions), and 24 custom commands
PTZ Function UpdatesDriver upload supported
Supported Device ProtocolsPelco D, Pelco P, Dynacolor DynaDome, Cohu, Custom Camera
Transparent PTZ ControlControl PTZ cameras with legacy PTZ control panel or keyboard connected to a PC or VPort decoder
• Security
PasswordUser level password protection
FilteringBy IP address
• Environmental Limits
Operating TemperatureStandard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity5 to 95% (non-condensing)
VibrationIEC 60068-2-6, 2 to 13.2 Hz: 2 mm (peak-peak); 13.2 to 100 Hz: 0.7g; 1.50 hrs/axis
IEC 60068-2-6, 3 to 9 Hz: 7 mm (peak-peak); 9 to 150 Hz: 1.0g; 1.86 hrs/axis
ShockIEC 60068-2-27, 20g/11ms
Altitude2000 m
Ingress ProtectionIEC 60529, IP30
• Standards and Certifications
SafetyUL 60950-1
EMICISPR 22, FCC Part 15B Class A
EMSEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV
IEC 61000-4-6 CS: 10 V
IEC 61000-4-8
• MTBF (mean time between failures)
Time465,000 hrs
StandardTelcordia SR332
• Warranty
Warranty Period5 years
DetailsSee www.moxa.com/warranty
• Minimum Viewing System Requirements
CPUPentium 4, 2.4 GHz or above
Memory512 MB memory or above
OSWindows XP/2000 with SP4 or above, Windows Vista, Windows 7
BrowserInternet Explorer 9.x or above
MultimediaDirectX 9.0c or above
• Software Development
VPort SDK PLUSIncludes CGI commands, ActiveX Control, and API library for customized applications or system integration for third-party developers (the latest version of SDK is available for download from Moxa’s website).
StandardONVIF

Available Models

Model No.Description
VPort 364A4-channel H.264/MJPEG industrial video encoder with 1 10/100BaseT(X) port, 0 to 60°C operating temperature
VPort 364A-M-SC4-channel H.264/MJPEG industrial video encoder with 1 multi-mode, SC connector port, 0 to 60°C operating temperature
VPort 364A-S-SC4-channel H.264/MJPEG industrial video encoder with 1 single-mode, SC connector port, 0 to 60°C operating temperature
VPort 364A-T4-channel H.264/MJPEG industrial video encoder with 1 10/100BaseT(X) port, -40 to 75°C operating temperature
VPort 364A-M-SC-T4-channel H.264/MJPEG industrial video encoder with 1 1 multi-mode, SC connector port, -40 to 75°C operating temperature
VPort 364A-S-SC-T4-channel H.264/MJPEG industrial video encoder with 1 1 single-mode, SC connector port, -40 to 75°C operating temperature

Building Tougher IP Cameras for Tougher Environments

Moxa’s commitment to reliability and quality is built into all of our IP cameras, which are used for oil & gas, transportation, and railway waysides, as well as many other industrial applications that require rugged products for harsh environments. Watch this video to gain a better understanding of how we design and manufacture our IP cameras, which includes taking strict measures at each phase of product development, selecting the best raw material, and conducting a complete product inspection.

Download White Paper

What separates an industrial IP camera from the rest? Our white paper identifies why industrial-grade perform better than their conventional counterparts in the toughest applications.https://www.moxa.com/support/request_catalog_detail.aspx?id=1438

backtotop
vport-364a-series-safenergy-i-din-moxa-ti-vit-nam