MPI-502

Multifunction Electrical Installations Meter

Danh mục: Thiết bị đo điện đa năng

Datasheet

User Manual

Declarations of conformity

Firmware for MPI-502

Mô tả Specs Details Overview Components Packages Resources Additional Modules Complementary products Architecture Tools Benefits Features Customer Ordering
Thông số Specs Details Overview Components Packages Resources Additional Modules Complementary products Architecture Tools Benefits Features Customer Ordering

Short circuit loop parameters measurements:

measurements of short circuit loop impedance in networks with rated voltage: 220/380 V, 230 V/400 V, 240/415 V and frequency 45…65 Hz,
measurements of short circuit loop impedance with current 15 mA without tripping the circuit breaker.

Testing the RCD breakers of AC, A types:

testing of prompt, short-delay (general) and selective RCDs for the rated current values 10, 30, 100, 300, 500 mA,
IA measurement
RE and UB measurement without tripping the circuit breaker,
extended RCD test function AUTO, with measurement of Z_L-PE with current 15 mA – measurement of I_A and t_A during one RCD tripping.

Detection of the replacement L and N in the socket and automatic conversion in the meter.

Low voltage resistance measurements of protective circuits and junctions:

measurement of resistance with ±200 mA current
calibration of test leads – possibility of using any length of test leads,
low current resistance measurement with accoustic signalling

Rapid check for the correct connection of PE wire using touch electrode.

Measurement of mains voltage and frequency.

Power supply from LR6 batteries or NiMH accumulators (option).

The device meets the requirements of IEC 61557 standard.

MPI-502 is equipment to perform complete test and verify on electrical installations according to the most common safety standards (IEC 61557, VDE 0100, BS7671).

Short circuit loop impedance measurement Z_L-PE, Z_L-N, Z_L-L

Measurment using 7,6/13,3 A current – Measurement range according to
IEC 61557: 0,13…1999 Ω
(for 1,2 m lead) and 0,19…1999 Ω (for WS-01 and WS-04).

Display range	Resolution	Accuracy
0,00…19,99 Ω	0,01 Ω	±(5% m.v. + 3 dgt)
20,0…199,9 Ω	0,1 Ω
200…1999 Ω	1 Ω

Nominal work voltage: Un_L-N/ Un_L-L: 220/380 V, 230/400 V, 240/415 V,
Voltage operating range: 100…264 V (for Z_L-PE i Z_L-N) and 100…440 V (for Z_L-L),
Nominal network frequency fn: 50 Hz, 60 Hz,
Max. test current: 23 A (230 V), 44 A (440 V),
PE terminal connection corectores check with the help of touch electrode

Readings of fault loop impedance R and fault loop reactance X_L

Display range	Resolution	Accuracy
0,00…19,99 Ω	0,01 Ω	±(5% m.v. + 5 digits) of Z_S value
20,0…199,9 Ω	0,1 Ω	±(5% m.v. + 5 digits) of Z_S value

calculated and displayed for Z_S<200 Ω.

Short circuit loop impedance Z_L-PE in mode RCD – without RCD tripping
Measurement using <15 mA,current measurement range in accordance with IEC 61557: 0,51…1999,9 Ω

Display range	Resolution	Accuracy
0,00…19,99 Ω	0,01 Ω	±(6% m.v. + 10 dgt)
20,0…199,9 Ω	0,1 Ω	±(6% m.v. + 5 dgt)
200…1999 Ω	1 Ω	±(6% m.v. + 5 dgt)

test without tripping the RCD for I_Δn ≥ 30 mA,
nominal work voltage: Un: 220 V, 230 V, 240 V,
voltage operating range:180…270 V,
frequency operating range fn: 50 Hz, 60 Hz
PE terminal connection correctness check with the help of touch electrode

Readings of fault loop impedance R and fault loop reactance X_L (without tripping the RCD)

Display range	Resolution	Accuracy
0,00…19,99 Ω	0,01 Ω	±(6% m.v + 10 dgt) of Z_S value
20,0…199,9 Ω	0,1 Ω	±(6% m.v + 5 dgt) of Z_S value

calculated and displayed for Z_S<200 Ω.

RCD parameters test (voltage range 180…270 V):
RCD tripping test and measurment of tripping time t_A (for t_A function)

Breaker Type	Test Current Multiplier	Range	Resolution	Accuracy
Standard	0,5*I_Δn	0…300 ms	1 ms	± (2% m.v. + 2 dgt)
	1*I_Δn	0…300 ms
	2*I_Δn	0…150 ms
	5*I_Δn	0…40 ms
Selective	0,5*I_Δn	0…500 ms
	1*I_Δn	0…500 ms
	2*I_Δn	0…200 ms
	5*I_Δn	0…150 ms

Precision of the differential current: 0,5*I_Δn:-8…0% for 1*I_Δn, 2*I_Δn, 5*I_Δn: 0…8%

Voltage measurement

Range	Range	Accuracy
0,0 V…299,99 V	0,1 V	±(2% m.v. + 6 dgt)
300 V…500 V	1 V	±(2% m.v + 2 dgt)

Frequency measurement

Range	Range	Accuracy
45,0 V…65,0 Hz	0,1 Hz	±(1% m.v. + 1 dgt)

Touch voltage measurement referred to the rated residual current (U_B)

Range	Resolution	Test Current	Accuracy
0..9,9 V	0,1 V	0,4 x I_Δn	10% m.v. ± 5 dgt
10,0..99,9 V	0,1 V	0,4 x I_Δn	0…15% m.v.

Measurementof the RCD disconection current I_A for sine waveform testing current

Selected Current	Range	Resolution	Test Current	Accuracy
10 mA	3,3…10,0 mA	0,1 mA	_{0,3 x IΔ}_{n…1,0 x IΔ}_n	±5%I_Δn
30 mA	9,0…30,0 mA	0,1 mA
100 mA	33…100 mA	1 mA
300 mA	90…300 mA
500 mA	150…500 mA

It is posible to start the measurement from the positive or negative half of the forced leaking current

RCD I_A tripping current measurement for unidirectional pulsating residual current

Selected Current	Range	Resolution	Test Current	Accuracy
10 mA	4…20,0 mA	0,1 mA	0,35xI_Δn..2,0xI_Δn	±10%I_Δn
30 mA	12,0…42,0 mA	0,1 mA	0,35xI_Δn..1,4xI_Δn
100 mA	40,0…140 mA	1 mA
300 mA	120…420 mA	1 mA

Measurement is possible for a positive or negative forced leakage current.

Low voltage test of the circuit and insulation continuity
Measurement range in accordance with IEC61557:0,12…400 Ω
Test of PE wire continuity using a ±200 mA current

Range	Resolution	Accuracy
0,00…19,99 Ω	0,01 Ω	±(2% m.v + 3 dgt)
20,0…199,9 Ω	0,1 Ω
200…400 Ω	1 Ω

Voltage on open terminals: 4…9 V,
Test current at R<2 Ω: min. 200 mA,
Autocalibration of test leads
Measurements for both polarizations of the current

The device meets the requirements of EMC standards EN 61326 – 1:2006 and EN 61326 – 2-2:2006.

Electric safety:

type of insulation: double, according to EN 61010 – 1 and IEC 61557
measurement category: IV 300 V (III 600 V) according to EN 61010 – 1
protection class acc. to EN 60529: IP67

Other technical data:

dimentions: 220 x 98 x 58 mm
weight: ~1 kg
Auto OFF time: 300, 600, 900 second
number of measurements Z and RCD (for NiMH batteries): >5000 (2 per minute)

„m.v.” measured value.